TM 5-3895-383-24 f. Push and hold the "preset" button down until flashing indicator   begins   to   flash   under   the   first   number position  (fourth  position  to  the  left  of  the  decimal), then   release.      Momentarily   pushing   the   "preset" button will cause the display number in that position to change.  Use the "preset" button to make the position show zero (0). g. Use the "preset" button to move the flashing indicator and   change   the   display   numbers   until   the   display shows 0062.00 mm. h. Push  and  hold  the  "preset"  button  until  the  flashing (P) is shown in the upper right corner of the display, and   then   release.      Momentarily   push   the   "preset button so the flashing (P) and the zeros to the left of 62.00 mm disappear. i. The indicator can now be turned OFF if desired.  The indicator   will   retain   the   preset   number   in   memory (only  one  preset  number  is  retained).    To  recall  the preset  number,  repeat  Steps  la  through  Id.    Then momentarily push the "preset" button so the flashing (P) and the zeros to the left of 62.00 mm disappear. j. Turn   the   indicator   OFF.      Make   sure   the   indicator plunger   is   extended   out   fully.      Repeat   steps   1a through   1d.      Then   momentarily   push   the   "preset" button so the flashing (P) and the zeros to the left of 62.00 mm disappear. 2. Install  the  3S3268  Contact  Point  [25.45  mm  (1.0  in) excluding threads] on the dial indicator stem. 3. Install  1U8869  Digital  Dial  Indicator  (9)  in  the  collet  of 4C4716 Timing Fixture (2).  Leave the collet loose. 4. Put   the   dial   indicator   and   timing   fixture   (2)   on   the 1U8702     Injector     Timing     Block     (3)     and     1U6678 Calibration Fixture (4) as shown.  Make sure locating pin (C)  in  left  side  of  timing  fixture  (2)  engages  hole  in calibration  fixture  (4).    Install  bolt  (B)  on  the  right  side and    tighten    to    secure    timing    fixture    (2)    firmly    to calibration fixture (4).  The long pin of timing fixture (2) must  be  in  the  hole  located  in  the  center  of  injector timing block (3).  The ends of the injector timing block and surface of calibration fixture must be clean. 5. Position the 1U8869 Digital Dial Indicator in the bracket so the indicator display shows 55.40 mm ±   0.40   mm   and   tighten   the   collet.      Turn   OFF   the indicator.      This   step   is   to   ensure   that   the   indicator plunger has adequate travel in both directions. 6. Repeat steps 1a through 1d. 7. Momentarily   push   the   "preset"   button.      The   display should  show  62.00  mm.    Lift  up  on  the  injector  timing block slightly, the display should increase in the positive direction.  If this is not true repeat steps 2 through 7. Fuel Timing Dimension (5)  Tappet  (6)  Adjustment  screw.    (7)  Shoulder.    (D)  Fuel Timing Dimension. 8. Make  sure  the  top  surfaces  of  injector  tappet  (5)  and shoulder (7) are clean and dry. 4C4716 Timing Fixture Installed (2)  4C4716  Timing  Fixture.    (6)  Adjustment  screw.    (8)  Inlet manifold.  (9) 118869 Digital Dial Indicator. NOTE: After  timing  fixture  (2)  has  been  installed  on  the inlet   manifold,   do   not   rotate   the   engine.      The timing fixture may be damaged. 9. Remove bolt (B) from timing fixture (2).  While holding up   collet   sleeve   (A),   gently   put   1U8869   Digital   Dial Indicator (9) and 4C4716 Timing Fixture (2) in position on the inlet manifold over the injector to be checked. 6-74