e. Quantity Incorporated in Unit. Indicates the
Code
Explanation
C ............... Crew or Operator maintenance
quantity of the item used in the assembly group. A "V"
O ............... Organizational maintenance
appearing in this column in. lieu of a quantity indicates
F ............... Direct Support maintenance
that a definite quantity cannot be indicated, (e.g., shims,
H ............... General Support maintenance
spacers, etc.).
(3) Recoverability code indicates whether
f. Fifteen-Day Organizational Maintenance
unserviceable items should be returned for recovery or
(1) Items authorized for use as required but not
salvage.
Items not coded are expendable.
for initial stockage are identified with an asterisk in the
Recoverability codes are:
allowance column.
(2) The allowance columns are divided into four
Code
Explanation
subcolumns. Indicated in each subcolumn is the total
quantity of special tools authorized for the number of
R
Applied to repair parts, (assemblies and components)
equipments supported. (Not Applicable)
special tools and test equipment which are considered
g. Thirty-Day DS/ GS Maintenance Allowance
economically reparable at direct and general support
(1) Items authorized for use as required but not
maintenance levels. When the item is, no longer
economically repairable, it is normally disposed of at the
for initial stockage are identified with an asterisk in the
GS level. When supply considerations dictate, some of
allowance column.
these repair parts may be listed for automatic return to
(2) The allowance columns are divided into three
supply for depot level repair as set forth in AR 710-50.
subcolumns. The quantitative allowance of special tools
When so listed, they will be replaced by supply on an
exchange basis.
for DS / GS levels of maintenance will represent initial
S
Repair parts, special tools, test equipment and assemblies
stockage for a 30-day period for the number of
'which are economically reparable at DSU and GSU
equipments supported. (Not Applicable)
activities and which normally are furnished by supply on
h. Items Authorized.
an exchange basis. When items are determined by a
(1) Items authorized for use as required but not
GSU to be uneconomically reparable, they will be
evacuated to a depot for evaluation and analysis before
for initial stockage are identified with an asterisk in the
final disposition.
allowance column.
T
High dollar value recoverable repair parts, special tools and
(2) This column indicates the total quantity of
test equipment which are subject to special handling and
special tools required for distribution and contingency
are issued on an exchange basis. Such items will be
evacuated to the depot for overhaul or final disposition.
planning purposes. (Not Applicable)
Communication-Electronics and missile support items
i. Illustration. This column is divided as follows:
will be repaired / overhauled only at depots.
(1) Figure number. Indicates the. Figure number
U
Repair parts, special tools and test equipment specifically
of the illustration on which the item is shown.
selected for salvage by reclamation units because of
precious metal content, critical materials, high dollar
(2) Item number. Indicates the callout number
value or reusable casings or castings.
used to reference the item on the illustration.
b. Federal Stock Number. Indicates the Federal
4. Special Information
stock number assigned to the item and will be used for
a. Parts which require manufacture or assembly of a
requisitioning purposes.
maintenance level higher than that authorized for
c. Description. Indicates the Federal item name and
installation will indicate in the source column the higher
any additional description of the item required. Assembly
maintenance level.
components and subassemblies are indented under major
b. The following publications pertain to roller and its
assemblies. The abbreviation "w / e" when used as part
components.
of the nomenclature, indicates the Federal stock number,
TM 5-2805-258-14
Operator, organizational, direct
includes all armament, equipment, accessories, and
support and general support
repair parts issued with the item. A part number or other
maintenance manual:
Engine,
reference number is followed by the applicable five-digit
gasoline, 10 hp, Military Standard
Federal supply code for manufacturers in parenthesis.
models (model 2A042-2 and
Repair parts quantities included in kits and sets are shown
2A042-3).
in front of the repair part name. Material required for
TM 5-2805-258-24P
Organizational, direct and general
manufacture or fabrication is identified.
support maintenance repair parts
d. Unit of Measure (U/M). A two-character alphabetic
and special tool lists: Engine, 10
abbreviation indicating the amount or quantity of the item,
hp,
as used, upon which the allowances are based, e.g., ft.,
ea., pr., etc.
D-2
